KGD IC
Xtal:1
DDR3 init.
DRAMC init done. 
Calculate size.
DRAM size=128MB
Set new TRFC.
ddr-1200


7528DRAMC V1.7 (0)

Press 'x' or 'b' key in 1 secs to enter or skip bootloader upgrade.


EN7528 at 2021年 01月 15日 星期五 20:08:19 CST version 1.1 free bootbase

Set SPI Clock to 50 Mhz
spi_nand_probe: mfr_id=0xcd, dev_id=0xea
Using Flash ECC.
Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_FS35ND01GS1Y2, Flash Size=0x8000000
bmt pool size: 81 
BMT & BBT Init Success 

  GE Rext AnaCal Done! (4)(0x1c)  

Press any key in 8 secs to enter boot command mode.
................................................................................



==> boot flag = 1
Decompress to 80002000 free_mem_ptr=80E00000 free_mem_ptr_end=807B0000
from slave
Uncompressing [LZMA] ...  done.
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 3.18.21 (pengjia@localhost) (gcc version 4.6.3 (Buildroot 2015.08.1) ) #18 SMP Fri Aug 5 18:50:15 CST 2022
__l2cmem:0x807490c0, _l2cmem_end:0x807490c0, l2cmem_size:0 Bytes
memsize:128MB
EcoNet EN7528 SOC prom init
bootconsole [early0] enabled
CPU0 revision is: 0001992f (MIPS 1004Kc)
Determined physical RAM map:
 memory: 07ffe000 @ 00002000 (usable)
Wasting 64 bytes for tracking 2 unused pages
MIPS: machine is econet,en751221
Zone ranges:
  Normal   [mem 0x00002000-0x07ffffff]
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x00002000-0x07ffffff]
Initmem setup node 0 [mem 0x00002000-0x07ffffff]
Detected 3 available secondary CPU(s)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
PERCPU: Embedded 9 pages/cpu @81104000 s5952 r8192 d22720 u36864
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32510
Kernel command line: 
log_buf_len individual max cpu contribution: 4096 bytes
log_buf_len total cpu_extra contributions: 12288 bytes
log_buf_len min size: 16384 bytes
log_buf_len: 32768 bytes
early log buf free: 14176(86%)
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Writing ErrCtl register=0006cebd
Readback ErrCtl register=0006cebd
nmi base is 81154200
Memory: 118364K/131064K available (7452K kernel code, 1308K rwdata, 1636K rodata, 208K init, 612K bss, 12700K reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:64


tc3162_time_init: Init bus timeout and watchdog

set rbus timeout as NMI then enable it
CPU frequency 900.00 MHz
plat_time_init: Entered, mips_timer_ack ptr is [80007fc4]

 Using 200.000 MHz high precision timer.
r4k_clockevent_init: setup_irq OK, irq is [52]

console [ttyS0] enabled
console [ttyS0] enabled
bootconsole [early0] disabled
bootconsole [early0] disabled
Calibrating delay loop... 591.87 BogoMIPS (lpj=2959360)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys debug
34K sync es set to 0.
Config7: 0x80090500
launch: starting cpu1
launch: cpu1 gone!
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU1 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 1: done.
launch: starting cpu2
launch: cpu2 gone!
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU2 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 2: done.
launch: starting cpu3
launch: cpu3 gone!
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU3 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 3: done.
Brought up 4 CPUs
NET: Registered protocol family 16
PCIe 7528 PHY init  
PCIe driver version: 7528.2.20190226
EN7528 pcie_init
check pcie link up status: 
isRC0_LINKUP=1 
isRC1_LINKUP=1 
registering PCI controller with io_map_base unset
Initializing Ecnt Event Netlink Socket

Initializing Econet Event Netlink Socket nl_sk = 87d34400

usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
pci_bus 0000:00: root bus resource [io  0x1f600000-0x1f61ffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:01.0: BAR 8: assigned [mem 0x20100000-0x202fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
pci 0000:02:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit pref]
pci 0000:02:00.0: BAR 2: assigned [mem 0x20200000-0x20203fff 64bit pref]
pci 0000:02:00.0: BAR 4: assigned [mem 0x20204000-0x20204fff 64bit pref]
pci 0000:00:01.0: PCI bridge to [bus 02]
pci 0000:00:01.0:   bridge window [mem 0x20100000-0x202fffff]
NET: Registered protocol family 8
NET: Registered protocol family 20
Switched to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1

 mt7512_pcie_fixup: 0x1438 = 20000014 
 mt7512_pcie_rc0_retrain: 70 = 0047d811 80 = 01608c12
 mt7512_pcie_fixup: 0x3438 = 20100015 
 mt7512_pcie_rc1_retrain: 80 = 0147dc12 80 = 01608c12
RC1 Link Traing Result: 10120008
TC3162 hardware watchdog module loaded.
futex hash table entries: 1024 (order: 4, 65536 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.23)
msgmni has been set to 231
io scheduler noop registered (default)
ttyS0 at I/O 0xbfbf0003 (irq = 5, base_baud = 7200) is a TC3162
ECNT ring buffer init success
brd: module loaded

SPI Flash Init Start
Found no SPI flash device
IS_SPIFLASH=0x0, IS_NANDFLASH=0x1, (0xBFA10114)=0x6)
Set SPI Clock to 50 Mhz
spi_nand_probe: mfr_id=0xcd, dev_id=0xea
Using Flash ECC.
Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_FS35ND01GS1Y2, Flash Size=0x8000000
spi nand flash
tc3162: flash device 0x01000000 at 0x1c000000
EN7512 mtd init: spi nand probe enter
[spi_nand_setup] : Enter 
nand: device found, Manufacturer ID: 0xcd, Chip ID: 0xea
nand: Unknown _SPI_NAND_DEVICE_ID_FS35ND01GS1Y2
nand: 128MiB, SLC, page size: 2048, OOB size: 64
nand_scan_ident ok
[spi_nand_setup]: chip size =  0x8000000, erase_shift=0x11
bmt pool size: 81 
BMT & BBT Init Success 

parsing <0[bootloader],0[romfile],25m[tclinux],25m[tclinux_slave]>
partition 7: name <tclinux_slave>, offset ffffffff, size 1900000, mask flags 0
partition 4: name <tclinux>, offset ffffffff, size 1900000, mask flags 0
partition 1: name <romfile>, offset ffffffff, size fffffffe, mask flags 0
partition 0: name <bootloader>, offset ffffffff, size fffffffe, mask flags 0
Creating 9 MTD partitions on "EN7512-SPI_NAND":
0x000000000000-0x000000040000 : "bootloader"
0x000000040000-0x000000080000 : "romfile"
0x000000080000-0x00000045b19e : "kernel"
mtd: partition "kernel" doesn't end on an erase block -- force read-only
0x00000045b19e-0x000000f4b19e : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x000000080000-0x000001980000 : "tclinux"
0x000001980000-0x000001d5b252 : "kernel_slave"
mtd: partition "kernel_slave" doesn't end on an erase block -- force read-only
0x000001d5b252-0x00000283b252 : "rootfs_slave"
mtd: partition "rootfs_slave" doesn't start on an erase block boundary -- force read-only
0x000001980000-0x000003280000 : "tclinux_slave"
0x000006dc0000-0x000007000000 : "reservearea"


rootfs_slave
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
register rtpci
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)


=== pAd = c0181000, size = 7338240 ===

<-- RTMPAllocAdapterBlock, Status=0
pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
RTMPInitPCIeDevice():device_id=0x7663
mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a01, pAd->ChipID=0x7663
mt7663_init()-->
<--mt7663_init()
<-- RTMPAllocTxRxRingMemory, Status=0
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
USB driver version: 7528.3.20190226
7528 USB PHY config, enable port0 port1
port 0 u2_slew_rate_cal_7528
FM_OUT value = 138(0x0000008A)
SR calibration value = 4
port 1 u2_slew_rate_cal_7528
FM_OUT value = 137(0x00000089)
SR calibration value = 4
xhci-hcd xhci-hcd.0: xHCI Host Controller
xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0: irq 10, io mem 0x1fb90000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
xhci-hcd xhci-hcd.0: xHCI Host Controller
xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver cypress_m8
usbserial: USB Serial support registered for DeLorme Earthmate USB
usbserial: USB Serial support registered for HID->COM RS232 Adapter
usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter
usbcore: registered new interface driver ftdi_sio
usbserial: USB Serial support registered for FTDI USB Serial Device
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1849 buckets, 7396 max)
ctnetlink v0.93: registering with nfnetlink.
nf_conntrack_rtsp v0.7 loading
nf_conntrack_rtcp v0.7 loading
port #0: 8027
nf_nat_rtsp v0.7 loading
nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net>
nf_tables_compat: (c) 2012 Pablo Neira Ayuso <pablo@netfilter.org>
IPv4 over IPsec tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
8021q: 802.1Q VLAN Support v1.8
tc3162ser_startup 
VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
Freeing unused kernel memory: 208K (80a4c000 - 80a80000)
open /proc/tc3162/dbg_msg fail
open /proc/tc3162/dbg_msg fail
busybox init and set aff=8=
tc3162ser_startup 
tc3162ser_startup 

init started:  BusyBox v1.00 (2022.08.01-01:48+0000) multi-call binary
tc3162ser_startup 
chmod: /userfs/profile.cfg: Read-only file system
Ebtables v2.0 registered
insmod: cannot open module `/lib/modules/3.18.21/kernel/net/ipv4/netfilter/ipt_REDIRECT.ko': No such file or directory
attackprotector: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
/usr/etc/init.d/rcS: 81: /userfs/bin/dbus_apps_info: not found
chmod: /userfs/profile.cfg: Read-only file system
mtd[readflash]:device=reservearea tclen=262144 tcoffset=1310720
Unlocking reservearea ...
Reading from reservearea to /tmp/prolinecwmppararead ... 

00000000h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000010h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000020h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000030h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000040h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000050h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000060h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000070h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000080h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
00000090h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
000000a0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
000000b0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
000000c0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
000000d0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
000000e0h: FFMAXNET DPI interface Loaded
insmod: cannot open module `/lib/modules/tcfullcone.ko': No such file or directory
TCSUPPORT_IPV6


tcaccesslimit version: accesslimit V1.2.0.0 (Dec 30 2019-19:16:35).
TC3162 LED Manager 0.1 init


tcledctrl version: tcledctrl V1.1.0.0 (Aug  1 2022-09:41:42).
find led.conf error

led path:/userfs/led.conf

tccicmd V1.1.0.0 (Aug  1 2022-09:41:44)


SIFMaster 0.1 init

===== Interface 0 is ON =====


Register sifm cmd


soft_ratelimit_init
svchost_random: ubusd urandom read with 92 bits of entropy available
parse_print_conf: Path = /lib/libcfg_clisvc.so 
svchost_parse_print_conf: Entry = svc_cfg_main 
svchost_parse_print_conf: Param = 111 
svc_cfg_start: ........ 
/tmp/cfg_load is not exist
Load cfg from file [/var/romfile.cfg] ..... 
ctromfile.cfg
insmod ETH_LAN driver
Check romfile pass!

mtd[readflash]:device=reservearea tclen=262144 tcoffset=524288
Unlocking reservearea ...
Reading from reservearea to /tmp/tc_backupromfile ... 
ECNT_HOOK_ERROR occur. ECNT_API_XPON_MODE_GET:200
[BK_ROMFILE_FLAG]/userfs/bin/mtd readflash /tcpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:2
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:2
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
cpu:1, nbq:1
mp/tc_backupromfile 262144 524288 reservearea
macType = 0
tso_proc_init.
netif_napi_add() called with weight 256 on device lan_int2_if
/tmp/cfg_load is not exist
ctromfile.cfg
svc_cfg_start: ........ ok [20001030]! 
ether.c:v1.00-NAPI 29.Mar.2015
eth0: FE MAC Ethernet address: 00:E0:0F:2B:24:AE
Use Internal switch ,type 10
tcPhyVerLookUp 2463 9491 
 7528 Ge, 
 [tcPhyInit] in  [tcPhyInit] out , r31 = (9, 0x0) 

 7528 GbE eco_rev (0x1) &0xff(0x1)

 GE Rxet cal (1)(1)(1)(0x1f)  

 GE Rxet cal (2)(1)(1)(0x1e)  

 GE Rxet cal (3)(1)(1)(0x1d)  

  GE Rext AnaCal Done! (4)(0x1c)  

  GE Rext AnaCal Done! (4)(0x1c)  

  GE R45 zcal_idx (28) (0x1c) 

  GE R45 AnaCal Done! (4) (0x41)(0xc1) 

  GE R45 zcal_idx (28) (0x1c) 

  GE R45 AnaCal Done! (4) (0x41)(0xc1) 

  GE R45 zcal_idx (28) (0x1c) 

  GE R45 AnaCal Done! (4) (0x41)(0xc1) 

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

 GE Tx offset AnaCal Done! (5)(0x5)  

 GE Tx offset AnaCal Done! (6)(0x26)  

 GE Tx offset AnaCal Done! (3)(0x3)  

 GE Tx offset AnaCal Done! (2)(0x22)  

 GE Tx amp AnaCal Done! (10) (0x16)

 GE Tx amp AnaCal Done! (14) (0x12)

 GE Tx amp AnaCal Done! (10) (0x16)

 GE Tx amp AnaCal Done! (13) (0x13)

tcPhyVerLookUp 2463 9491 
 7528 Ge, 
 [tcPhyInit] in  [tcPhyInit] out , r31 = (10, 0x0) 

 7528 GbE eco_rev (0x1) &0xff(0x1)

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

  GE R45 zcal_idx (28) (0x1c) 

  GE R45 AnaCal Done! (4) (0x41)(0xc1) 

  GE R45 zcal_idx (29) (0x1d) 

random: nonblocking pool is initialized
  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

 GE Tx offset AnaCal Done! (1)(0x21)  

 GE Tx offset AnaCal Done! (1)(0x1)  

 GE Tx offset AnaCal Done! (2)(0x22)  

 GE Tx offset AnaCal Done! (3)(0x3)  

 GE Tx amp AnaCal Done! (7) (0x19)

 GE Tx amp AnaCal Done! (11) (0x15)

 GE Tx amp AnaCal Done! (9) (0x17)

 GE Tx amp AnaCal Done! (13) (0x13)

tcPhyVerLookUp 2463 9491 
 7528 Ge, 
 [tcPhyInit] in  [tcPhyInit] out , r31 = (11, 0x0) 

 7528 GbE eco_rev (0x1) &0xff(0x1)

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

  GE R45 zcal_idx (28) (0x1c) 

  GE R45 AnaCal Done! (4) (0x41)(0xc1) 

 GE Tx offset AnaCal Done! (1)(0x21)  

 GE Tx offset AnaCal Done! (1)(0x21)  

 GE Tx offset AnaCal Done! (1)(0x21)  

 GE Tx offset AnaCal Done! (4)(0x24)  

 GE Tx amp AnaCal Done! (15) (0x11)

 GE Tx amp AnaCal Done! (16) (0x10)

 GE Tx amp AnaCal Done! (14) (0x12)

 GE Tx amp AnaCal Done! (13) (0x13)

tcPhyVerLookUp 2463 9491 
 7528 Ge, 
 [tcPhyInit] in  [tcPhyInit] out , r31 = (12, 0x0) 

 7528 GbE eco_rev (0x1) &0xff(0x1)

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

  GE R45 zcal_idx (28) (0x1c) 

  GE R45 AnaCal Done! (4) (0x41)(0xc1) 

  GE R45 zcal_idx (29) (0x1d) 

  GE R45 AnaCal Done! (3) (0x2f)(0xaf) 

 GE Tx offset AnaCal Done! (1)(0x1)  

 GE Tx offset AnaCal Done! (1)(0x21)  

 GE Tx offset AnaCal Done! (1)(0x1)  

 GE Tx offset AnaCal Done! (2)(0x22)  

 GE Tx amp AnaCal Done! (20) (0xc)

 GE Tx amp AnaCal Done! (15) (0x11)

 GE Tx amp AnaCal Done! (16) (0x10)

 GE Tx amp AnaCal Done! (8) (0x18)

svchost_parse_print_conf: Path = /lib/libwan_svc.so 
svchost_parse_print_conf: Entry = svc_wan_main 
svchost_parse_print_conf: Param = 111 
svc_wan_init: ...... reg event ok 
svchost_parse_print_conf: Path = /lib/libwlan_svc.so 
svchost_parse_print_conf: Entry = svc_wlan_main 
svchost_parse_print_conf: Param = 111 
svchost_parse_print_conf: Path = /lib/libwan_related_svc.so 
svchost_parse_print_conf: Entry = svc_wan_related_main 
svchost_parse_print_conf: Param = 111 
svchost_parse_print_conf: Path = /lib/libother_svc.so 
svchost_parse_print_conf: Entry = svc_other_main 
svchost_parse_print_conf: Param = 111 
svchost_parse_print_conf: Path = /lib/libcentral_ctrl_svc.so 
svchost_parse_print_conf: Entry = svc_central_ctrl_main 
svchost_parse_print_conf: Param = 111 
svc_wan_related_init: ...... reg event ok 
svc_wlan_init: ...... reg event ok 
svc_other_init: ...... reg event ok 
svchost_parse_print_conf: Path = /lib/libvoip_svc.so 
svchost_parse_print_conf: Entry = svc_voip_main 
svchost_parse_print_conf: Param = 111 
svc_centrl_ctrl_init: ...... reg event ok 
PID=244 event receive pthread_create OK, keep going......
svc_voip_ivoip_mgr_polling_pthread created.
nt: num = 4
svc_voip_init: ...... reg event ok 
voip_mgr_polling_pthread entered.
eth0: starting interface.
netif_start_queue
val_string:add v4 - 445 - -

dport:0, sport:445, daddr:0, saddr:0
vtag_drv_init


tc_multiwan version: tcsmux V1.1.0.0 (Dec 30 2019-19:16:40).


tcportbind version: tcportbind V1.1.0.0 (Dec 30 2019-19:16:43).
device eth0 entered promiscuous mode
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
svchost_get_event_val: get param fail [0] 
/bin/sh: cannot create /proc/tc3162/lan_ip_mask: Directory nonexistent
/bin/sh: cannot create /proc/tc3162/lan_ip_mask: Directory nonexistent
br0: port 1(eth0) entered forwarding state
br0: port 1(eth0) entered forwarding state
SIOCSIFADDR: File exists
svchost_get_event_val: get param fail [0] 
ra0       no private ioctls.

read WLAN driver from rt_device faileget_itf_hwaddr 1270: ioctl open fail
d,set get_wdev_by_idx: invalid idx(0)
with default valu==>check_wireless_ac_card: error when get ra0 EEPROM data
e!
WPSAget_wdev_by_idx: invalid idx(0)
ctiveStatus = NULL
WPSOOBActive = NULL
ReCounterActive = NULL
WPSGenPinCode = NULL
insmod: cannot open module `/lib/modules/brg_shortcut.ko': No such file or directory
Open /dev/hwnat0 pseudo device failed
ra0       no private ioctls.

ra0       no private ioctls.

ra0       no private ioctls.

ra0       no private ioctls.

write_wlan11ac_config:wifimgr_lib_set_wdskey fail.
write_wlan11ac_config:wifimgr_lib_set_wdskey fail.
write_wlan11ac_config:wifimgr_lib_set_wdskey fail.
write_wlan11ac_config:wifimgr_lib_set_wdskey fail.

qos_discipline_initmtd[readflash]:device=reservearea tclen=512 tcoffset=1835008
Unlocking reservearea ...
Reading from reservearea to /tmp/RT30xxEEPROM.bin ... 
device eth0.1 is not a slave of br0
killall: wscd: no process killed
svchost_get_event_val: get param fail [0] 

read WLAN driver from rt_device failed,set with default value!
==>check_wireless_ac_card: error when get ra0 EEPROM data
get_wdev_by_idx: invalid idx(0)
WPSActiveS==>check_wireless_ac_card: error when get ra0 EEPROM data
tatus get_wdev_by_idx: invalid idx(0)
= NULL
WPSOOBAc==>check_wireless_ac_card: error when get ra0 EEPROM data
tive =get_wdev_by_idx: invalid idx(0)
 NULL
ReCounterA==>check_wireless_ac_card: error when get ra0 EEPROM data
ctive get_wdev_by_idx: invalid idx(0)
= NULL
WPSGenPinCode = NULL
insmod: cannot open module `/lib/modules/3.18.21/kernel/net/sched/act_mirred.ko': No such file or directory
write_wlan11ac_config:write CountryRegion to data file fail.
debug 4.
insmod: cannot open module `/lib/modules/3.18.21/kernel/net/sched/cls_fw.ko': No such file or directory
insmod: cannot open module `/lib/modules/3.18.21/kernel/net/sched/sch_htb.ko': No such file or directory
write_wlan11ac_config:wifimgr_lib_set_wdskey fail.
write_wlan11ac_config:wifimgr_lib_set_wdskey fail.
write_wlan11ac_config:wifimgr_lib_set_wdskey fail.
write_wlan11ac_config:wifimgr_lib_set_wdskey fail.
insmod: cannot open module `/lib/modules/3.18.21/kernel/net/sched/sch_prio.ko': No such file or directory
SIOCGIFFLAGS: No such device
mtd[readflash]:device=reservearea tclen=1536 tcoffset=307200
Unlocking reservearea ...
Reading from reservearea to /tmp/MT7610EEPROM.bin ... 
device eth0.2 is not a slave of br0
insmod: cannot open module `/lib/modules/igmpsnoop.ko': No such file or directory
killall: wscd: no process killed
insmod: cannot open module `/lib/modules/mldsnooping.ko': No such file or directory
svc_other_evt_internal_deal: param get fail.svchost_get_event_val: get param fail [0] 
killall: udhcpd: no process killed
device eth0.3 is not a slave of br0
udhcpd (v0.9.9-pre) started
Jan  1 00:00:12 TCSysLog udhcpd[517]: udhcpd (v0.9.9-pre) started

/bin/sh: /userfs/bin/dproxy: not found
svc_other_evt_internal_deal: param get fail.svchost_get_event_val: get param fail [0] 
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Using intrapositioned negat

ion (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
device eth0.4 is not a slave of br0
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
device eth0 is already a member of a bridge; can't enslave it to bridge br0.
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`)Ralink HW NAT Module Enabled
HWNAT Module enabled with Type:L2B/IPv4/IPv6/DS-LITE/6RD, foeSize:80B, foeNum:16384
IP check use Black List
.
four ports
device eth0 left promiscuous mode
br0: port 1(eth0) entered disabled state
device eth0.1 is not a slave of br0
ip6tables v1.4.10: can't initialize ip6tables table `filter': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.4.10: can't initialize ip6tables table `filter': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.4.10: can't initialize ip6tables table `filter': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.4.10: can't initialize ip6tables table `filter': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.4.10: can't initialize ip6tables table `filter': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.4.10: can't initialize ip6tables table `filter': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
device eth0.1 entered promiscuous mode
br0: port 1(eth0.1) entered forwarding state
br0: port 1(eth0.1) entered forwarding state
device eth0.2 is not a slave of br0
ip6tables v1.4.10: can't initialize ip6tables table `filter': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
ip6tables v1.4.10: can't initialize ip6tables table `filter': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
device eth0.2 entered promiscuous mode
br0: port 2(eth0.2) entered forwarding state
br0: port 2(eth0.2) entered forwarding state
device eth0.3 is not a slave of br0
device eth0.3 entered promiscuous mode
br0: port 3(eth0.3) entered forwarding state
br0: port 3(eth0.3) entered forwarding state
device eth0.4 is not a slave of br0
device eth0.4 is not a slave of br0
device eth0 entered promiscuous mode
br0: port 4(eth0) entered forwarding state
br0: port 4(eth0) entered forwarding state
SIOCGIFFLAGS: No such device
interface eth0.5 does not exist!
device eth0 left promiscuous mode
br0: port 4(eth0) entered disabled state
device eth0.1 is already a member of a bridge; can't enslave it to bridge br0.
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720
Unlocking reservearea ...
R

eading from reservearea to /tmp/productlinecwmpfile ... 
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
device eth0.2 is already a member of a bridge; can't enslave it to bridge br0.
iptables: Bad rule (does a matching rule exist in that chain?).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
device eth0.3 is already a member of a bridge; can't enslave it to bridge br0.
device eth0.4 is not a slave of br0
SIOCGIFFLAGS: No such device
interface eth0.5 does not exist!
Illegal target name 'vbind_entry0_chain'.
Chain 'vbind_entry0_chain' doesn't exist.
Illegal target name 'vbind_entry1_chain'.
Chain 'vbind_entry1_chain
url_filter_init
' doesn't exist.
Illegal target name 'vbind_entry2_chain'.
Chain 'vbind_entry2_chain' doesn't exist.
Illegal target name 'vbind_entry3_chain'.
Chain 'vbind_entry3_chain' doesn't exist.
Illegal target name 'vbind_entry4_chain'.
Chain 'vbind_entry4_chain' doesn't exist.
Illegal target name 'vbind_entry5_chain'.
Chain 'vbind_entry5_chain' doesn't exist.
Illegal target name 'vbind_entry6_chain'.
Chain 'vbind_entry6_chain' doesn't exist.
Illegal target name 'vbind_entry7_chain'.
Chain 'vbind_entry7_chain' doesn't exist.
TCSUPPORT_CT_NETWORKMANAGESERVICE:no need to start utelnetd up in rcs!
Illegal target name 'vbind_entry8_chain'.
TC3162 hardware watchdog initialized
Chain 'vbind_entry8_chain' doesn't exist.
TCSUPPORT_CT_NETWORKMANAGESERVICE:no need to use inetd!
Illegal target name 'vbind_entry9_chain'.
Chain 'vbind_entry9_chain' doesn't exist.
Illegal target name 'vbind_entry10_chain'.
Chain 'vbind_entry10_chain' doesn't exist.
TCSUPPORT_CT:no need to use tftpd!
Illegal target name 'vbind_entry11_chain'.
Chain 'vbind_entry11_chain' doesn't exist.
Illegal target name 'vbind_entry12_chain'.
Chain 'vbind_entry12_chain' doesn't exist.
Illegal target name 'vbind_entry13_chain'.
Chain 'vbind_entry13_chain' doesn't exist.
Illegal target name 'vbind_entry14_chain'.
Chain 'vbind_entry14_chain' doesn't exist.
Illegal target name 'vbind_entry15_chain'.
Chain 'vbind_entry15_chain' doesn't exist.
Illegal target name 'vbind_entry16_chain'.
Chain 'vbind_entry16_chain' doesn't exist.
Illegal target name 'vbind_entry17_chain'.
mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720
Unlocking reservearea ...
Reading from reservearea to /tmp/productlinecwmpfile ... 
Chain 'vbind_entry17_chain' doesn't exist.
Illegal target name 'vbind_entry18_chain'.
Chain 'vbind_entry18_chain' doesn't exist.
Illegal target name 'vbind_entry19_chain'.
Chain 'vbind_entry19_chain' doesn't exist.
Illegal target name 'vbind_entry20_chain'.
Chain 'vbind_entry20_chain' doesn't exist.
Illegal target name 'vbind_entry21_chain'.
Chain 'vbind_entry21_chain' doesn't exist.
Illegal target name 'vbind_entry22_chain'.
[01/Jan/1970:00:00:17 +0000] boa: server version Boa/0.94.13
[01/Jan/1970:00:00:17 +0000] boa: server built Aug  1 2022 at 09:49:03.
[01/Jan/1970:00:00:17 +0000] boa: starting server pid=1015, port 80
Chain 'vbind_entry22_chain' doesn't exist.
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
Illegal target name 'vbind_entry23_chain'.
Chain 'vbind_entry23_chain' doesn't exist.
Illegal target name 'vbind_entry24_chain'.
Chain 'vbind_entry24_chain' doesn't exist.
BusyBox v1.00 (2022.08.01-01:48+0000) multi-call binary

Usage: taskset [OPTIONS] [mask] [pid | command [arg]...]

Illegal target name 'vbind_entry25_chain'.
Chain 'vbind_entry25_chain' doesn't exist.
The path is invalid, and the path should include entry.
Plugin pppoe loaded.
PPPoE Plugin Initialized
Plugin pppoe called.
setting line discipline hook
Sending PADI
ses->filt->stag==NULL
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===eget_wdev_by_idx: invalid idx(0)
rrno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
get_wdev_by_idx: invalid idx(0)
TCSUPPORT_WLAN_SW_RPS
get_wdev_by_idx: invalid idx(0)

ecnt_rps_napi_init===
get_wdev_by_idx: invalid idx(0)
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
get_wdev_by_idx: invalid idx(0)
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
0===errno:0
 errmessage:Success
1===errno:0
 errmessage:Success
2==errno:0
 errmessage:Success
7613 sw rps
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
tc3162ser_startup 
get_wdev_by_idx: invalid idx(0)

Please press Enter to activate this console. get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
register mt_drv
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)


=== pAd = c1d01000, size = 1037304 ===

<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc1c00000, csr_addr=0xc1c00000!
device_id =0x7603
RtmpChipOpsHook(474): Not support for HIF_MT yet!
mt7603_init()-->
mt_bcn_buf_init(224): Not support for HIF_MT yet!
<--mt7603_init()
load_dev_l1profile()-->
RtmpOSFileOpen(): Error 2 opening /etc/wireless/l1profile.dat
load_dev_l1profile() Open file "/etc/wireless/l1profile.dat" failed, try embedded default!
load l1profile failed!
load_dev_l1profile()-->
RtmpOSFileOpen(): Error 2 opening /etc/wireless/l1profile.dat
load_dev_l1profile() Open file "/etc/wireless/l1profile.dat" failed, try embedded default!
rt28xx_open l1profile failed!
TX_BCN DESC a407c000 size = 320
RX[0] DESC a407e000 size = 2048
RX[1] DESC a407f000 size = 2048
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
Key1Str is Invalid key length(1) or Type(0)
Key2Str is Invalid key length(1) or Type(0)
Key3Str is Invalid key length(1) or Type(0)
Key4Str is Invalid key length(1) or Type(0)
[PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
[PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
PS_RETRIEVE = 1
FW Version:CL173766_R
FW Build Date:20171110105932\00
CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000002
RtmpChipOpsEepromHook::e2p_type=4, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=1
RtmpChipOpsEepromHook: E2P type(4), E2pAccessMode = 4, E2P default = 1
NVM is BIN mode
1. Phy Mode = 14
Cal Free IC!!
@@@  NICReadEEPROMParameters : pAd->FWLoad=0 
Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 38
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(14): Not support for HIF_MT yet!
NICInitializeAsic(588): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
mt7603_init_mac_cr()-->
AsicSetMacMaxLen(1936): Set the Max RxPktLen=1024!
<--mt_mac_init()
	WTBL Segment 1 info:
		MemBaseAddr/FID:0x28000/0
		EntrySize/Cnt:32/128
	WTBL Segment 2 info:
		MemBaseAddr/FID:0x40000/0
		EntrySize/Cnt:64/128
	WTBL Segment 3 info:
		MemBaseAddr/FID:0x42000/64
		EntrySize/Cnt:64/128
	WTBL Segment 4 info:
		MemBaseAddr/FID:0x44000/128
		EntrySize/Cnt:32/128
AntCfgInit(2714): Not support for HIF_MT yet!
MCS Set = ff ff 00 00 01
[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
AsicSetRalinkBurstMode(4380): Not support for HIF_MT yet!
RTMPSetPiggyBack(972): Not support for HIF_MT yet!
mt7603_switch_channel(): Switch to Ch#9(2T2R), BBP_BW=1
AsicSetTxPreamble(4367): Not support for HIF_MT yet!
AsicAddSharedKeyEntry(2102): Not support for HIF_MT yet!
AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0
Main bssid = 00:e0:0f:2b:24:ae
<==== rt28xx_init, Status=0
<==== 7592 sw_rps_init
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
mt7603_set_ed_cca: TURN ON EDCCA mac 0x10618 = 0xd7c87d0f, EDCCA_Status=1
jiffies=ffffa405, POLLING_MODE_DETECT_INTV=300

WiFi Startup Cost (ra0): 2.640s
device ra0 entered promiscuous mode
br0: port 4(ra0) entered forwarding state
br0: port 4(ra0) entered forwarding state
rai0: ===> main_virtual_if_open
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
RtmpOSFileOpen(): Error 2 opening /etc/wireless/l1profile.dat
Read file "/etc/wireless/l1profile.dat" failed(errCode=1)!
load l1profile failed!
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
driver_own()::Try to Clear FW Own...
driver_own()::Success to clear FW Own
APWdsInitialize():WdsEntry[0]
APWdsInitialize():WdsEntry[1]
APWdsInitialize():WdsEntry[2]
APWdsInitialize():WdsEntry[3]

<--RATE_PRIOR AllocateSpinLock
RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860_2G.dat
Open file "/etc/Wireless/RT2860/RT2860_2G.dat" failed!
SSID[0]=xxxx' 5G, EdcaIdx=0
cfg_mode=14
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Equal!
[TxPower] BAND0: 100
[PowerUpenable] BAND0: 0
[SKUenable] BAND0: 0
[PERCENTAGEenable] BAND0: 1
[BFBACKOFFenable] BAND0: 0
LinkTestSupport = 0
profile: FragThreshold[0]=2346
APEdca0
APEdca1
APEdca2
APEdca3
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
DfsZeroWait Support=0/0
DfsZeroWaitCacTime=255/255
RTMPSetProfileParameters(): ACSCheckTime[0]=0 seconds
read_itxbf: ITxBfEn = 1
read_itxbf: BSSID[0]
read_itxbf: MBSS[0] ITxBfEn = 1
read_itxbf: Common.ITxBfEn = 1
read_etxbf: ETxBfEnCond = 1
read_etxbf: BSSID[0]
read_etxbf: MBSS[0] ETxBfEnCond = 1
[PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
[PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
rtmp_read_wds_from_file(): WDS Profile
APWdsInitialize():WdsEntry[0]
APWdsInitialize():WdsEntry[1]
APWdsInitialize():WdsEntry[2]
APWdsInitialize():WdsEntry[3]
WDS-Enable mode=0
HT: WDEV[0] Ext Channel = BELOW
ChipI=7663, Value=0, pcie_aspm in profile=0
ICapMode = 0
WtcSetMaxStaNum: MaxStaNum:103, BssidNum:1, WdsNum:4, ApcliNum:1, MaxNumChipRept:24, MinMcastWcid:133
Top Init Done!
Use dev_alloc_skb
RX[0] DESC a71ea000 size = 8192
RX[1] DESC a73a8000 size = 8192
cut_through_init(): ct sw token number = 4095
cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
cut_through_token_list_init(): 841ec108,841ec108
cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
cut_through_token_list_init(): 841ec118,841ec118
Hif Init Done!
ctl->txq = c087a8fc
ctl->rxq = c087a908
ctl->ackq = c087a914
ctl->kickq = c087a920
ctl->tx_doneq = c087a92c
ctl->rx_doneq = c087a938
mt7663_fw_prepare():using E2 ROM patch
mt7663_fw_prepare():using E2 firmware
Parsing patch header
	Built date: 19111514483394b

	Platform: 7663
	HW/SW version: 0x6d702d31
	Patch version: 0x3830328a
	Target address: 0xdc000, length: 204096
patch is not ready && get semaphore success
Start address = 0xdc000, DL length = 204096, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
MtCmdPatchFinishReq
EventGenericEventHandler: CMD Success
release patch semaphore
WfMcuHwInit: Before NICLoadFirmware, check ICapMode = 0
Parsing CPU 0 fw tailer
	Chip ID: 0x08
	Eco version: 0x01
	Region number: 0x03
	Format version: 0x02
	Format flag: 0x01
	Ram version: 7663mp1827
	Built date: 20191115145002\00
	Common crc: 0x29717359
Parsing tailer region 0
	Decomp crc: 0x0
	Decomp size: 0x0
	Decomp block size: 0x0
	Target address: 0x112c00
	Download size: 277024
	Feature set: 0x27
Parsing tailer region 1
	Decomp crc: 0x0
	Decomp size: 0x0
	Decomp block size: 0x0
	Target address: 0x2018400
	Download size: 70704
	Feature set: 0x07
Parsing tailer region 2
	Decomp crc: 0x0
	Decomp size: 0x0
	Decomp block size: 0x0
	Target address: 0x40100000
	Download size: 14720
	Feature set: 0x07
	Release info: header tag = 0, total length = 0
Start address = 0x112c00, DL length = 277024, Data mode = 0x8000000f
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x2018400, DL length = 70704, Data mode = 0x8000000f
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x40100000, DL length = 14720, Data mode = 0x8000000f
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
MtCmdFwStartReq: override = 0x1, address = 0x112c00
EventGenericEventHandler: CMD Success
MCU Init Done!
efuse_probe: efuse = 511161
RtmpChipOpsEepromHook::e2p_type=4, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=1
RtmpChipOpsEepromHook: E2P type(4), E2pAccessMode = 4, E2P default = 1
NVM is BIN mode
Use the default /etc/Wireless/RT2860AP_AC/RT30xxEEPROM.bin bin image!
rtmp_ee_load_from_bin::bin FileName=/etc/Wireless/RT2860AP_AC/RT30xxEEPROM.bin
Load EEPROM Buffer from /etc/Wireless/RT2860AP_AC/RT30xxEEPROM.bin
Cal Free IC!!
mt7663_cal_free_data_get
now bb MainSsid mac 00:e0:0f:2b:24:af
Country Region from e2p = 0
mt7663_antenna_default_reset() todo
RTMPReadTxPwrPerRate(444): Don't Support this now!
RcRadioInit(): DbdcMode=0, ConcurrentBand=1
RcRadioInit(): pRadioCtrl=87230e38,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf
AntCfgInit(2955): Not support for HIF_MT yet!
MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!!
RtmpOSFileOpen(): Error 2 opening /etc_ro/Wireless/RT2860AP/Sku_default.dat
--> Error opening file </etc_ro/Wireless/RT2860AP/Sku_default.dat>
MtPwrLimitLoadParamHandle: Read Power Table Error!!
MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!!
RtmpOSFileOpen(): Error 2 opening /etc_ro/Wireless/RT2860AP/Backoff_default.dat
--> Error opening file </etc_ro/Wireless/RT2860AP/Backoff_default.dat>
MtPwrLimitLoadParamHandle: Read Power Table Error!!
EEPROM Init Done!
mt_mac_init()-->
mt_mac_pse_init(2958): Don't Support this now!
mt7663_init_mac_cr()-->
mt7663_init_mac_cr(): TMAC_TRCR0=0x82783c92
MtAsicSetMacMaxLen(1073): Not support for HIF_MT yet!
<--mt_mac_init()
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
MAC Init Done!
MT7663BBPInit():BBP Initialization.....
	Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
	Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
MT7663BBPInit() todo
PHY Init Done!
RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860_2G.dat
Open file "/etc/Wireless/RT2860/RT2860_2G.dat" failed!
SSID[0]=xxxxx' 5G, EdcaIdx=0
cfg_mode=14
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Equal!
[TxPower] BAND0: 100
[PowerUpenable] BAND0: 0
[SKUenable] BAND0: 0
[PERCENTAGEenable] BAND0: 1
[BFBACKOFFenable] BAND0: 0
LinkTestSupport = 0
profile: FragThreshold[0]=2346
APEdca0
APEdca1
APEdca2
APEdca3
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
DfsZeroWait Support=0/0
DfsZeroWaitCacTime=255/255
RTMPSetProfileParameters(): ACSCheckTime[0]=0 seconds
read_itxbf: ITxBfEn = 1
read_itxbf: BSSID[0]
read_itxbf: MBSS[0] ITxBfEn = 1
read_itxbf: Common.ITxBfEn = 1
read_etxbf: ETxBfEnCond = 1
read_etxbf: BSSID[0]
read_etxbf: MBSS[0] ETxBfEnCond = 1
[PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
[PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
rtmp_read_wds_from_file(): WDS Profile
APWdsInitialize():WdsEntry[0]
APWdsInitialize():WdsEntry[1]
APWdsInitialize():WdsEntry[2]
APWdsInitialize():WdsEntry[3]
WDS-Enable mode=0
HT: WDEV[0] Ext Channel = BELOW
ChipI=7663, Value=0, pcie_aspm in profile=0
ICapMode = 0
tx_pwr_comp_init():NotSupportYet!
MtCmdSetMacTxRx:(ret = 0)
asic_bss_beacon_init(): NotSupportedFunc for this arch(HIF_MT)!
MtAsicSetChBusyStat(646): Not support for HIF_MT yet!
AsicDisableSync(): NotSupportedFunc for this arch(HIF_MT)!
MtAsicSetRalinkBurstMode(2219): Not support for HIF_MT yet!
MtAsicSetPiggyBack(590): Not support for HIF_MT yet!
WifiFwdSet::disabled=0
AsicSetPreTbtt(): NotSupportedFunc for this arch(HIF_MT)!
ap_ftkd> Initialize FT KDP Module...
Main bssid = 00:00:00:00:00:00
AsicSetRxFilter(): NotSupportedFunc for this arch(HIF_MT)!
MtCmdSetMacTxRx:(ret = 0)
AsicSetRxFilter(): NotSupportedFunc for this arch(HIF_MT)!
MtCmdSetMacTxRx:(ret = 0)
INIT REDUCE TCP ACK, rai0
<==== mt_wifi_init, Status=0
TxBfModuleEnCtrl:It's not DBDC mode
MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
MSTA_Init (1) ---> ApCli
Register MSTA IF (apclii0) , pAd->MSTANum = 1
Caller: SetCommonHT+0xb0/0x160

phy_mode=49, ch=0, wdev_type=2
ht_cap: ht_cap->HtCapInfo, 
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm, 
mdpu_density=0, ampdu_factor=3
WDS_Init():
The new WDS interface MAC = 00:00:00:00:00:00
  MacTabMatchWCID = 0
Caller: SetCommonHT+0xb0/0x160

phy_mode=49, ch=0, wdev_type=8
ht_cap: ht_cap->HtCapInfo, 
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm, 
mdpu_density=0, ampdu_factor=3
The new WDS interface MAC = 00:00:00:00:00:00
  MacTabMatchWCID = 0
Caller: SetCommonHT+0xb0/0x160

phy_mode=49, ch=0, wdev_type=8
ht_cap: ht_cap->HtCapInfo, 
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm, 
mdpu_density=0, ampdu_factor=3
The new WDS interface MAC = 00:00:00:00:00:00
  MacTabMatchWCID = 0
Caller: SetCommonHT+0xb0/0x160

phy_mode=49, ch=0, wdev_type=8
ht_cap: ht_cap->HtCapInfo, 
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm, 
mdpu_density=0, ampdu_factor=3
The new WDS interface MAC = 00:00:00:00:00:00
  MacTabMatchWCID = 0
Caller: SetCommonHT+0xb0/0x160

phy_mode=49, ch=0, wdev_type=8
ht_cap: ht_cap->HtCapInfo, 
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm, 
mdpu_density=0, ampdu_factor=3
Total allocated 4 WDS interfaces!
WtcSetMaxStaNum: MaxStaNum:103, BssidNum:1, WdsNum:4, ApcliNum:1, MaxNumChipRept:24, MinMcastWcid:133
cp_support_is_enabled: set Driver CP_SUPPORT to Mode 2.

==ecnt_wifi_rx_rps_hook===, pAd=c0181000
RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
wifi_sys_open(), wdev idx = 0
wdev_attr_update(): wdevId0 = 00:e0:0f:2b:24:af
[RcGetHdevByPhyMode]-- channel 0 fix for rdev fetching
[BuildChannelList] BandIdx = 0, PhyMode = 49, ChListNum = 13:
 [RadarStateCheck] RD_NORMAL_MODE  
phy_freq_adjust : no prim_ch value for adjust!
Caller: wlan_operate_init+0xa4/0x11c

phy_mode=49, ch=0, wdev_type=1
ht_cap: ht_cap->HtCapInfo, 
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm, 
mdpu_density=5, ampdu_factor=3
AP inf up for ra_0(func_idx) OmacIdx=0
AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
ApAutoChannelAtBootUp----------------->
ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1
AsicSetRxFilter(): NotSupportedFunc for this arch(HIF_MT)!
MtCmdSetMacTxRx:(ret = 0)
[AutoChSelBuildChannelListFor5G] ChListNum5G = 13
AsicSwitchChannel(): 5G Channel:149, then must be Channel_Band:1 !!
AsicSwitchChannel(): 5G Channel:153, then must be Channel_Band:1 !!
AsicSwitchChannel(): 5G Channel:157, then must be Channel_Band:1 !!
AsicSwitchChannel(): 5G Channel:161, then must be Channel_Band:1 !!
ApAutoChannelAtBootUp : Auto channel selection: Selected channel = 149, IsAband = 1
 AutoChSelUpdateChannel(): Update channel for wdev for this band PhyMode = 49, Channel = 149 
 [RadarStateCheck] RD_NORMAL_MODE  
AsicSwitchChannel(): 5G Channel:155, then must be Channel_Band:1 !!
ApAutoChannelAtBootUp<-----------------
[PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
Caller: SetCommonHT+0xb0/0x160

phy_mode=49, ch=149, wdev_type=1
ht_cap: ht_cap->HtCapInfo, 
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm, 
mdpu_density=5, ampdu_factor=3
wifi_sys_linkup(), wdev idx = 0
wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:135 for WDEV_TYPE:1
 LinkToOmacIdx = 0, LinkToWdevType = 1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196
UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0
MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 0
MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0
MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0
AsicSetTxStream(): NotSupportedFunc for this arch(HIF_MT)!
AsicSetRxStream(): NotSupportedFunc for this arch(HIF_MT)!
apidx 0 for WscUUIDInit
Generate UUID for apidx(0)
device rai0 entered promiscuous mode
br0: port 5(rai0) entered forwarding state
br0: port 5(rai0) entered forwarding state
Mode:Dhcp6s mode is not manual!
[svc_wan_related_ipmacfilter_write]953: g_ip_mac_flag = 0


parameter_init(), conReqDelay = 

parameter_init(), multiConReq = 

parameter_init(), itmsRebootFlag = tr069 tcapi mode is 1
ThreadedTimerCheck: get last for first time


mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!

mq=3, reserved=0,reserved2=0!!

send message ok!
shm_pool_lock ret:-1,errno:4,Unknown error! 

qos_queue_clear()

 ether qos gQueueMask is 0xf
ap_cmm_peer_assoc_req_action(): Receive Assoc Req from MAC - 06:f1:8e:2e:4b:3d
AP SETKEYS DONE - WPA2, AuthMode(7)=WPA2PSK, WepStatus(6)=AES, GroupWepStatus(4)=TKIP


get device is PCgoptionasdfasd = 1

get device is PCgoptionasdfasd = 1
Jan  1 00:01:52 TCSysLog udhcpd[523]: 
 i will reinit host.

Jan  1 00:01:52 TCSysLog udhcpd[523]: sending OFFER of 1

mq=3, reserved=0,reserved2=0!!92

send message ok!.168.1.2 (06:f1:8e:2e:4b:3d)




wifi_mac_entry_add(): send msg to lanhost.

mq=23, reserved=0,reserved2=0!!

send message ok!
BA - Send ADDBA request. StartSeq = 3,  FrameLen = 33. BufSize = 64

get device is PCgoptionasdfasd = 1
Jan  1 00:01:52 TCSysLog udhcpd[523]: sending ACK to 192.168.1.2 (06:f1:8e:2e:4b:3d)

MulticastFilterTableInsertEntry: already in Members list.
MulticastFilterTableInsertEntry: already in Members list.
Rcv Wcid(1) AddBAReq
Start Seq = 00000010
BA - Send ADDBA request. StartSeq = 1,  FrameLen = 33. BufSize = 64
MulticastFilterTableInsertEntry: already in Members list.
Rcv Wcid(1) AddBAReq
Start Seq = 00000010

tc3162ser_startup 

 login: admi